How to Hack Wifi password using cmd
How to hack wifi password: Hello Friends, In this article we will share some tricks that can help you to hack wifi password using cmd. You can experiment these trick with your neighbors or friends. It’s not necessarily that this trick will work with every wifi because of upgraded hardware. But you can still try this crack with wifi having old modems or routers.
Also, read:
- 15 Best Wifi Hacker tool for PC and Android of 2017
- Hack wifi Password Using Wireshark
- 50+ Password and wifi hacking software to become a Pro
- How to hack WiFi Password on Android
- 5 Android Hacking Software that cannot be missed
If you want to Increase your Internet speed over a shared Internet network, then head over here. You will find steps to use NetCut, a very popular and free cracking software used to cut Internet connection of users by ARP spoofing hack.
It’s quite easy to crack if you follow our steps carefully. This trick will work with most of the wifi devices that have old hardware( modems and routers). For general knowledge, there are two types of wifi keys WEP and WPA. Both are explained below:
Types of WiFi security keys:
1: WEP: Wired Equivalent Privacy (WEP) is one of the widely used security key in wifi devices. It is also the oldest and most popular key and was added in 1999. WEP uses 128 bit and 256-bit encryption. With the help of this tutorial, you can easily get into 128-bit encryption and Hack WiFi password using CMD.
2: WAP and WAP2: Wi-Fi Protected Access is an another version of WiFi encryption and was first used in 2003. It uses the 256-bit encryption model and is tough to hack. WAP2 is an updated version of WAP and was introduced in 2006. Since then it has replaced WAP and is now been used mostly in offices and colleges worldwide.
Below are some steps to hack wifi password using cmd. Follow them carefully and you might get one of your neighbors passwords.
HOW TO HACK WIFI PASSWORD USING CMD
Hacking a Wi-Fi device is not always easy. You have to be careful of so many steps. Otherwise, you might even get caught. For easy and secure hacking, one should use the command prompt (cmd). Cmd is one of the most used features of Windows that gives you access to almost everything on a system. If used properly, you can even get inside other remote systems. To know more about cmd hacking check out our articles here.
Steps to Hack Wifi password using cmd:
1: Open command prompt by going to start and click on run command or enter windows+r, then type cmd and hit Enter
2: In command prompt window, type
netsh wlan show network mode=bssid
3: This command will show all the available WiFi network in your area
4: This is the last step. Just type:
netsh wlan connect name=(wifi name )
netsh wlan connect name=Mynet Sata1
and you will be connected to that WiFi network.
5: To disconnect it, type
netsh wlan disconnect
There are many other methods for exploiting a wifi to get its password. You can check them here. Also, note that these tutorials are for educational purpose only. To download WiFi hacking softwares, head to the download section.
Must Read:
5 Tools for Hacking wireless networks that can Actually Hack
Want to know more about command prompt hacks, visit here. You can also browse our other easy hacking tutorials here. If you are still facing any problems, you can comment below. If this tutorial is not working, then head up here to know about How to hack WiFi password using kali Linux.
How do I tell which ones the wifi name?
please tells the method to hack other’s wifi password that never connected to our laptop
before
Hey..
Please guide me how i can hack a WiFi password that is not listed on *User Profiles* list in cmd.exe.
I appreciate any answer
this method didn’t work sir.
I did as the instructions said, and it said “There is no such wireless interface on the system.” I’m not sure if it depends on the laptop, I have a Windows 10 HP Stream Notebook.
it’s working in 2017 or not?
There is no profile “*****” assigned to the specified interface. why is this happening?
hlo i have also this problems but i don’t know what i am doing?
how can i connect to wifi with password, i only able to connect known wifi network by this cmd line (netsh wlan connect name=”….”)which is already store my pc. i want to connect unknown but available network with password in my area by the cmd line. can you please help me out.
Gud
Hey! this is Kunal firstly, when i typed “netsh wlan show network mode=bssid” it came that ‘The wireless autoconfig service is not running’. Somehow i started the wireless autoconfig service and tyed this-“netsh wlan show network mode=bssid”, it came that ‘There is no wireless interface on the system’. So what to do next? i mean how to get the wireless interface on the system? please reply me a [email protected]
[email protected]
[email protected]
Thanks…
Mister your problem ‘There is no wireless interface on the system’ shows because you must put first wireless antennae to your pc so that it could recognize/search Wifi around you without it you’re only doomed It’s gonna be useless.